在线观看视频你懂的,999国产精品999久久久久久,凹凸av导航大全精品

By: Daniele

Daniele — Wed, 12 Apr 2023 11:22:18 +0000

Hi there. Phoenix simulator doesn’t recognize the usb Leonardo joystick. Serial debug monitor is working and tx movement are working on joy.CPL. What to do ?

By: Zdenek

Zdenek — Sun, 10 Jul 2022 22:03:57 +0000

In reply to montis. Thanks for reply

By: montis

montis — Sun, 10 Jul 2022 09:11:57 +0000

In reply to Zdenek. This project is based on Atmel microcontroller. You cannot swap straightforward to another type of MCU. Of course it is possible, but you have to port the code (make some adjustments/changes to code) to use is with XIAO boards.

By: Zdenek

Zdenek — Thu, 07 Jul 2022 21:19:47 +0000

Hi,
I’ve got Seeduino XIAO (https://www.seeedstudio.com/Seeeduino-XIAO-Arduino-Microcontroller-SAMD21-Cortex-M0+-p-4426.html) and I’m wondering, if boards with SAMD21 (like XIAO) could be used instead of Atmega32u4 boards. Unfortunately I’m not microcontroller expert. Do You know, if it has any chance to work?

By: cyberide

cyberide — Thu, 21 Oct 2021 12:23:21 +0000

After reading the description, I made one myself, but it doesn’t work completely. I checked that the value of the remote controller is coming out of the serial monitor, but after that, it is not recognized as a joystick in Windows 10 x64. What should I check?

By: cyberide

cyberide — Mon, 18 Oct 2021 16:13:14 +0000

I made one set but the gamepad device does not appear. Any way to know what the problem is? Check list or some debugging method?? I already tried “JOYSTICK_TYPE_JOYSTICK or JOYSTICK_TYPE_GAMEPAD” but it didn’t work
I used flysky fs-i6 and ia6b for this build. RC setting is i-bus ppm.
And I can see each channel data. It worked good.
Thank you in advance~

By: Marios

Marios — Fri, 15 Jan 2021 16:18:07 +0000

Hi, I have compiled it into a pro micro with an X4R receiver configured to ppm output.

I have successfully passed the calibration stage, where all 6 channels are identified and their min/max positions are stored.

This is where I get stuck. the pc reports the arduino as a game controller, but it does not see any movements from the transmitter, while the serial monitor is displaying the movements of the channels….

Any idea what I am missing?

Thanks in advance,
Marios

By: Sjoer van der Ploeg

Sjoer van der Ploeg — Tue, 12 Jan 2021 12:09:54 +0000

https://github.com/sfjuocekr/SBUS-joystick

For those who have a spare Teensy!

By: Aydra

Aydra — Mon, 30 Nov 2020 14:47:30 +0000

Hi, I have compiled it to pro micro using bayang RX.
adding Serial.print within the DEBUG code to check if the PPM stream readable from RX. and all is good, got 6 channel (4 AETR, 2 buttons).
But when I go to test it on JOY.CPL test tab I don’t get any response from the TX.
Already try changing JOYSTICK_TYPE_MULTI_AXIS or JOYSTICK_TYPE_JOYSTICK or JOYSTICK_TYPE_GAMEPAD.
Still no response, any clue what to check?

Regards

By: Robert Turpin

Robert Turpin — Fri, 23 Oct 2020 00:29:09 +0000

so I followed this guide, albeit not without a massive amount of issues along every step of the way. first I couldnt get my board to connect to my PC, but I was finally able to use another arduino and an FTDI adapter to finally burn the bootloader, then I was able to upload the sketch normally.

After uploading the sketch and connecting it via usb, it no longer shows up in device manager as an arduino, and it opens a comm port but does not show as a specific device, just shows an open comm port. In addition, it does not show up at all as a controller