Diatone Mamba F405 and F405 Mini stacks
Diatone has released Mamba stack F405 FC with F40A ESC, and mini stack version with F405 mini and F25A ESC back in the year 2018. The FC was also called Fury F4 and Fury F4M (Betaflight target was called Fury F4 OSD) and the stacks also were called Mamba Power Tower. These are one of the most popular stacks and have been updated several times.
Diatone Mamba stacks don’t not have User Manuals, but instead Diatone provides detailed connection diagrams (see below).
Diatone Mamba F405
First Diatone Mamba F405 stack was released in 2018-08
F405 MK2
2019-05: Diatone released an updated, so called MK2 versions of the Mamba F405 stacks. The main differences between the F405 MK1 and F405 MK2: rearranged majority of the pads, added the 9V output for DJI digital FPV support, almost completely new FC.
Diatone Mamba F405 MK2 with F40 ESC connection diagram:
Diatone Mamba F405 MK2 with F50 ESC connection diagram:
There are 5 status LEDs on the Mamba F405 (MK1 and MK2) flight controller. They are the status indicators for the following:
- Blue -> Betaflight (or other firmware) Status LED
- Orange -> Betaflight (or other firmware) Status LED
- Green -> 9V Power Rail Active
- White -> 5V Power Rail Active
- Red -> 3.3V Power Rail Active
Available @
Diatone: https://www.diatone.us/products/mamba-f405-mk%E2%85%B1-flight-controller-stack
Mamba F405 Power Tower specifications:
Item name: F405 Betaflight Flight Controller
Input power: 12-25V (3-6S)
BEC: 5V/1.5A
MCU: STM32F405
Gyro: MPU6000
Flash: 16MB
OSD: AT7456
Mounting hole: 30.5*30.5mm
Weight: 6g
Mamba F40 Esc
Description:
Item name: Mamba F40HV ESC
Input voltage: 3-6S (12.4V~25V)
Continue current: 40A×4
Burst current: 40/50A (6S)
BEC: NO
Mounting: 30mm / φM3
Weight: 10g
MAMBA F405 MK3
2021-01: Diatone released the updated MK3 versions of the Mamba F405 stacks. The main FC now comes in two versions Mamba F405 MK3 and a bit cheaper Mamba F405 MK3 Lite.
What are the differences between MK2 and MK3:
Fixed
1. Add I2C function
2. When you connect the USB, the receiver and OSD settings can be saved
3. Increase the pad area
4. LED signal selection （when Mamba Led sys available）
5. BEC short circuit protection
6. TVS instant high voltage protection 30V
Update
1. F405 models support F.prot（Most）
2. Upgrade the anti-interference cable
3. Use USB Type-C （Most）
Added
1. Add self-recovery insurance to the receiver’s 5V power supply
2. Increase the camera VCC power supply pad
3. Standard flight controller (30.5×30.5) adds spare pad
4. Gyro uses an independent Low Dropout Regulator (Low Dropout Regulator) and reduces ripple interference
Mamba F405 MK3 has 6 UARTS, two independent 5V/3A BEC, LED controller, Barometer
Available @
Specifications:
Name: Mamba Basic F405 MK3 FC
MCU: 168MHz STM32F405RGT6
IMU: MPU6000
Barometer: Yes
OSD: Yes
Blackbox: 16M Flash Memory
Uarts: 6 Set
ESC Soft: Dshot300/600/1200
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED/MB LED（ 4 Set 2812 LED）
F.Port: Yes
RSSI: Yes
Buzz: Yes
Input: 3~6S Lipo (12.6~25.2V)
TVS Protection: Yes
BEC: 3.3V/0.5A & 5V/3A (System Power)) 5V/3A(LED) & 9V/3A
MOUNTING: 30.5mm,M3
Diatone Mamba Basic F405 MK3 Stack connection diagram.
Diatone Mamba F405 MK3 stack is available with 40A and 50A 4in1 BLHeli_S ESC
Available @ Banggood:
Mamba F405 MK3 Lite has less UARTS, no barometer, no separate BEC for LEDs and no on board LED controller.
Specifications:
Item name: Mamba Basic F405 MK3 Lite Flight Control
MCU: 168MHz STM32F405RGT6
IMU: MPU6000
Barometer: No
OSD: Yes
Blackbox: 16M Flash Memory
Uarts: 5 Set
ESC Soft: Dshot300/600/1200
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED（4 Set 2812 LED）
F.Port: Yes
RSSI: Yes
Buzz: Yes
Input: 3~6S Lipo (12.6~25.2V)
TVS Protection: Yes
BEC: 3.3V/0.5A & 5V/3A & 9V/3A
MOUNTING: 30.5mm,M3
Diatone Mamba F405 MK3 Lite stack connection diagram:
Diatone Mamba F405 MK3 Lite stack is available with 40A and 50A 4in1 BLHeli_S ESC
Available @ Banggood:
Diatone Mamba F405 mini
Older revision of the Diatone F405 Mini MK2:
Current revision of the Diatone F405 Mini MK2:
Mamba F405 Mini MK2 connection diagram:
Available @
Mamba F405 Mini Power Tower Specification:
Item name: F405 Mini FC
INPUT: 2~4S LIPO (7.4V~16.8V)
BEC: 5V 1A
MCU: STM32F405
Gyro: MPU6000
FLASH: 16M
OSD: AT7456
MOUNTING: 20mm/M2
WEIGHT: 3.5g
Item name: Mamba F25HV ESC
Input voltage: 2~4S (7.4V~16.8V)
Continue current: 25A×4
Burst current: 30A (10S)
BEC: NO
Size: 30×30×5mm
Mounting: 20mm / φM2
Weight: 8g
Diatone Mamba F405US Mini MK3
2020-06 Diatone released MK3 version of the F405US Mini stack. This stack is available in two versions: standard FPV and DJI.
Mamba F405US Mini MK3 connection diagram with DJI FPV unit:
Available @
Diatone Mamba F405 Mini MK3 DJI
Mamba F405 Mini MK3 DJI connection diagram with GPS and TBS CRSF Nano:
Available @
F405 Mini MK3.5
2021-01 Diatone has upgraded the MK3 version and the new stack is called Mamba Basic F405 Mini MK3.5 stack. Pretty long name. The new version is available in two options: with 30A 4in1 BLHeli_S ESC and with 40A 4in1 BLHeli_s ESC. So the full name of the stack is… Diatone Mamba Basic F405 Mini MK3.5 F30 8bit stack. The 30A stack is capable to work with up to 5S battery and the 40A stack is up to 6S batery.
The full list of what was fixed/upgraded/added:
Fixed
- Add I2C function
- When you connect the USB, the receiver and OSD settings can be saved
- Increased pad area
- LED signal selection （when Mamba Led sys available）
- BEC short circuit protection
- TVS instant high voltage protection 30V
Update
- F405 models support F.port
- Upgrade the anti-interference cable
- Uses Type-C USB socket
- The pad area of Mini flight controller (20×20) increased by 140%
Added
- Add self-recovery insurance to the receiver’s 5V power supply
- Increased the camera VCC power supply pad
- Standard flight controller (30.5×30.5) adds spare pad
- Gyro uses an independent Low Dropout Regulator (Low Dropout Regulator) and reduces ripple interference
Diatone Mamba Basic F405 Mini MK3.5 connection diagram:
Diatone Mamba Basic F405 Mini MK3.5 User Manual: https://cdn.shopify.com/s/files/1/0027/2708/4144/files/MAMBA_Basic_F405_MINI_MK3.5.pdf
Available @
Diatone:
History: 2018-09-28 first published
2020-06-11 Mini MK3 was added
2021-01-10 F405 MK3 and F405 Mini MK3.5 were added
Related Posts
-
ESC Firmware Guide
In this concise overview, we’ll explore the evolution of ESC (Electronic Speed Controller) firmware, -
BetaFPV SuperG NanoTX – first dual diversity ELRS TX
BetaFPV, in collaboration with the ELRS developer team, has unveiled another first in the
About Author
Hey, the “ Mamba F405 Mini MK3 DJI connection diagram” has an error that’s since been corrected (where the GPS serial is connected inline with the CRSF nano) – it might be good to swap that out or pull it? Seems people are finding it, it just showed up in the TBS Lounge again. Thank you so much!
Thanks for the heads up! The diagram was is partially correct, you just can’t use GPS and TBS CRSF Nano simultaneously. Didn’t find the corrected one so made an edit to the diagram.
But, why 405? Just to make something “affordable”/low price for something that doesn’t require high performance? Aka long range quads? I doubt F405 is good for 3” quads as they are very agile and require fast processing time.
F405 are powerful enough for any quad. KISS (V1) runs perfectly on the F3 MCU. But yes, the future is in F7/H7 MCU.
Bought 405 mk 3.5 30 amp stack . XM+ Reciever binds but no response to the controller .
You should connect the XM+ SBUS wire to the pad marked RC. Then it is all the matter of settings in the Betaflight Configurator. Use UART1 as Serial receiver input. Also don’t forget to set receiver to the “Serial based receiver” and “SBUS” in the Configuration tab.
bonjour est ce que les esc de la f405 dji sont compatible avec une fc f405 dji mk2?
Should be compatible. Both boards have socket for DJI AIR connector.
All f***ng garbage. Cant wait to do reviews and tutorials. XXXO