Rumors: DJI Action 2 camera
New DJI Action 2 camera specifications were leaked out. DJI is preparing to release new Osmo Action 2 camera with improved specs and different form factor.
DJI Action 2 camera will have new 1/1.7 sensor, 155 degree FOV, better low-light performance, RockSteady Digital Video Stabilization V2.0, bigger battery life plus external battery module, improved/upscaled built-in audio quality. Camera supports resolutions up to 4K / 60fps with the aspect ratio of 4:3.
Camera dimensions 39x39x22.3mm and weight is 56 grams.
DJI Action 2 camera will have attachable LCD display with extended battery. Extended battery allows to record up to 195min.
Possible photo of the new camera.
DJI Action 2 specifications:
Source: Twitter
You want more? Ok … this is from the #DJI #Action2 manual. Including the #specs list. Field of view is now 155 degrees in stead of 145. Comes with a necklace too. #thebigleak@DroneXL1 @geeksvana @dronedj @techdronemedia @DronewatchNL @DronefriendlyB @dronemodelismo @OsitaLV pic.twitter.com/SxSRm4VMhx
— Jasper Ellens – 27 Leaks (@JasperEllens) September 23, 2021
Related Posts
-
BetaFPV SuperG NanoTX – first dual diversity ELRS TX
BetaFPV, in collaboration with the ELRS developer team, has unveiled another first in the -
Radiomaster Pocket Radio
Radiomaster has unveiled its latest creation, the Radiomaster Pocket Radio, a compact but feature-packed
About Author
a new session? ??
https://www.notebookcheck.net/fileadmin/Notebooks/News/_nc3/FANPmwIVIAQhAWS.jpg
Looks good. I guess it fill fit the Session mounts with minimal adaptation or will it not? 39x39mm vs 38x38mm.
i guess it should
but it’s much shorter
to use that space with a bigger battery, new mounts would have to be made
This is a pipe dream in the best case scenario. It isn’t going to fit. The Hero5 Session is 38mm x 38mm x 36mm, almost a perfect cube.
DJI has this listed as 39mm x 39mm x 22.3mm.
Putting depth to the side for now, you are going from a smaller camera sized at 38mm square to a slightly larger one at 39mm square. Meaning the front face area is 1444 square mm on the Session and 1541 square mm on the DJI 2.
This alone is going to be a problem. If you were going from larger camera to smaller camera (ie, the opposite of what we are doing here) then MAYBE you could make it work with a little bit of added padding or paper on one side of the case.
Once you include depth, you can see why it won’t happen. The Session is 36mm in depth and the DJI 2 is only 22.3 mm in depth.
In the end you have have a larger camera face (it is only larger by 77 mm square but that is a lot more than a little wiggle room) and the body of the DJI 2 is just over 60% the size of the session.
By the time you figure out all the sizes needed to fit it to an old Session case with a piece made in Fusion360, you could have already made a case specifically for the DJI 2 which will always be a better fit.
Thanks for detailed comment! Yes, (unfortunately) you are right. This ‘slight’ size mismatch is killing the mount compatibility.
cam mounts are not made from granite
tpu mounts flex easily
the frontal surface area is a useless measurement
the only thing that matters is height and depth
since the sides of the mount are open, you can just jam the cam in and stuff foam in the back, to push it forward
it’s only 1mm