Review: BetaFPV M03 VTX

BetaFPV M03 VTX is the updated version of their?M01 VTX. The earlier version had one fixed 25mW power output level. The new M03 VTX is outputting from 25mW?up to 350mW. Lets take a look at this VTX.

Specifications:
Output power: 25/100/200/350mW (adjustable)
Supply voltage range: 4.5-5.5V
Weight: 1.1g (antenna not included)
VTX internal size: 18x14mm
Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz
Channel SEL: SmartAudio
Modulation type: FM
Frequency control: PLL
All harmonic: Max -50dBm
Frequency stability: ±100KHz (Typ.)
Frequency precision: ±200KHz (Typ.)
Channel carrier error: ±1.5dB
Antenna port: 50 Ω
Operating temperature: -10℃~+80℃
Camera connector: JST-0.8, compatible with camera like BETAFPV C01, BETAFPV C02 and NewBeeDrone BeeEye.

Closer look

BetaFPV M03 VTX package contains M03?VTX, with linear antenna?and 5 silicone wires for soldering this VTX to the FC.

Top side view.

On the bottom side you can find the push button for setting the power output level and the LED for power level output indication.

M03 VTX has JST-0.8 connector socket that is direct plug in compatible with BETAFPV C01 (discontinued),?BETAFPV C02?and?NewBeeDrone BeeEye?cameras that have such connector preinstalled. There is also solder pads for soldering the camera vires directly to the VTX.

There is a spacer between the antenna and the PCB an the antenna is fixed to the the PCB with small piece of the heat shrink.

Size and weight

Size comparison with Eachine NanoVTX.

Size comparison with Happymodel WhoopVTX.

BetaFVP M03 VTX weights 1.6 grams including the antenna.

And weights only 1.1 grams without the antenna.

Pinouts and connection diagrams

BetaFPV M03?VTX connection pinout

BetaFPV M03 VTX connection diagram

Power output measurements

I’ve connected the BetaFPV M03 VTX?to the ImmersionRC RF power meter V2 via short u.Fl to SMA pigtail. VTX was cooled with fan while taking the measurements.

First test –?25mW?output setting. In my test it is outputting about 36mW?(15.5dBm).

At the?100mW?setting it outputs?108 mW?(20.3Bm). Pretty spot on.

At the?200mW?setting it outputs?358 mW?(25.55 dBm). This is almost double than the nominal power output!

And at the max setting of?350mW?it outputs?441 mW?(26.4 Bm).

Next test – how stable its power output if the VTX is not cooled actively. So I’ve turned off the fan and let the VTX running for the 5min. The measured power output was 333mW (25.2dBm). Pretty good. The M03 VTX maintains the high power output even without active cooling.

Below are the RF power outputs for all power levels. Measured at?Raceband,?CH5.

Power output vs frequency for?25mW?power level on?Raceband.

Power output vs frequency for?100mW?power level on?Raceband.

Power output vs frequency for?200mW?power level on?Raceband.

Power output vs frequency for 350mW?power level on?Raceband.

The deviations are really significant. On the 25mW power output you can get the 62mW on the CH1 and the 25mW on the CH8. On the?350mW? power output level you can expect the M03 VTX to output even?770mW of the RF power on the?CH1. and only 277mW on the CH8. The power output of this little VTX is really impressive!

Changing the VTX settings

BetaFPV M03 VTX settings (band, channel and power output level) can be changed by Betaflight OSD control. There is no way how to change the band and the channel manually and You can only change the power output level by pressing the button.

VTX has one multicolor LED indicator for power level display. Green light is for 25mW, Yellow for 100mW, Red for 200mW and Purple light indicates 350mW.

 

Betaflight setup and VTX Tables

BetaFPV M03 VTX is working with TBS SmartAudio protocol. You should connect the SmartAudio wire from the VTX to the any available TX pad on the FC.

In the Betaflight Configurator, choose TBS SmartAudio protocol in the Peripherals tab

Read more about SmartAudio here:?Guide: SmartAudio VTX control and how to set it up

If you are using (or planning to use) the Betaflight versions 4.x? and want to control the VTX by Betaflight OSD, then you should set up the VTX Tables.

Read more on setting up the VTX tables here:?VTX Tables and how to set them up

Open Betaflight Configurator, connect to the flight controller, select “Video Transmitter” tab. Load the VTX table from the file by clicking on the [Load from file] button.

Select the VTX table file. There can be separate VTX table files for?US?and?EU?region as there are different range of the allowed frequencies to use. (Hint: European table has only the?3 channels?on?Raceband).

Once VTX file is loaded, you should see the VTX table with the right frequencies and power settings.

Don’t forget to hit the [Save] button.

 

BetaFPV M03 VTX Betaflight VTXtable file:?https://drive.google.com/file/d/1qqowepTWmj_be-WsJ-jtUsAx5_aNsos7/view

Conclusions & final thoughts

BetaFPV M03 VTX is the smallest VTX from BetaFPV. Despite being so small it is really powerful as it can output 350mW and even more. I have recorded the power output up to 771mW on the Raceband, CH1. Power output ranges from 62?mW?to?25 mW?on the 25mW power setting and from?771 mW?to?277 mW?on the 350mW setting. On the lower channels you can get enormous amount of the power output. Have that in mind if you are looking for the maximum FPV range.

BetaFPV M03 VTX has probably the best power to weight ratio in the market. It has 401mW/1g ratio. Currently unmatched. It also set my personal record of the nano sized VTX absolute maximum power reached – 771mW.

The bottom line – M03 VTX is definitely one of the best VTX options for whoops and ultralight quadcopters.

BetaFPV M03 VTX is available @

BetaFPV: https://betafpv.com/products/m03-25-350mw-5-8g-vtx

Disclaimer: This item was supplied by BetaFPV for a fair and unbiased review. BetaFPV never asked for a positive review and never influenced my opinion in any way. I’m trying my best to stay uninfluenced and give only my own opinion. All affiliate links if there are any help me purchase items for future reviews and tests.